GRC構件在建筑行業的地位是很重要的。咱們經常在古典建筑風格的建筑物上都會看到GRC構件。
山東GRC構件雖然具有防潮、耐腐蝕性，可是，為了添加其使用壽命，也需求咱們進行護理的。
GRC components play an important role in the construction industry. We often see GRC components on buildings with classical architectural style. Although GRC components have moisture-proof and corrosion resistance, we also need to take care of them in order to increase their service life.
1、GRC構件避免沾上灰塵和污漬：可以用吸塵器來清潔砂巖背景墻而且要確保吸塵器是軟毛刷，因為硬設備可能會刮傷砂巖。
1. Avoid dust and stains on GRC components: use a vacuum cleaner to clean the sandstone background wall and ensure that the vacuum cleaner is a soft brush, because hard equipment may scratch the sandstone.
2、安裝好后盡快密封：密封口可以充當砂巖背景墻的保護層，防止灰塵和污漬的進入以及砂巖內的水分蒸發，因為它和空氣中的化學物質發生反應可能會損壞砂巖背景墻。
2. Seal as soon as possible after installation: the sealing opening can serve as the protective layer of the sandstone background wall to prevent the entry of dust and stains and the evaporation of water in the sandstone, because it may damage the sandstone background wall if it reacts with chemical substances in the air.
3、GRC構件不要接觸油污：因為油或污垢會導致砂巖背景墻染色，如果接觸到了應該盡快清理避免被砂巖吸收。
3. GRC components shall not be exposed to oil stain: because oil or dirt will lead to the staining of sandstone background wall, if it is exposed, it shall be cleaned as soon as possible to avoid being absorbed by sandstone.
4、避免使用瓷磚清洗劑清潔：瓷磚清洗劑會使墻壁瓷磚褪色應該用干凈的軟布和溫水，經常擦拭可以防止有害化學物質的沉積。
4. Avoid the use of ceramic tile cleaning agent: ceramic tile cleaning agent will make the wall tiles fade. Clean soft cloth and warm water should be used. Frequent wiping can prevent the deposition of harmful chemicals.
GRC構件的實際養護過程中，需要分為以下幾個階段來進行：
The actual curing process of GRC components needs to be divided into the following stages:
1、修飾之后，通常需要采用潔凈而且的聚乙烯薄膜來將模具包住，以放置GRC構件中的水分受到蒸發和風的影響，同時也有助于保持水化熱，在養護的初期應保證GRC構件能夠擁有足夠的強度，使其在脫模與搬運的過程中不會受到損傷。
1. After finishing, it is usually necessary to wrap the mold with clean polyethylene film to place the moisture in the GRC component affected by evaporation and wind, which also helps to maintain the heat of hydration. At the initial stage of curing, it is necessary to ensure that the GRC component can have sufficient strength, so that it will not be damaged during demoulding and handling.
2、為脫模之后的GRC構件繼續進行保護，以免其會受到光照、風雨空氣低濕度的影響，一般情況下仍采用塑料薄膜將GRC構建包裹住，以免受到陽光的直接照射，通過噴濕霧也可以保持局部的濕度。
2. In order to protect GRC components after demoulding from the impact of light and low humidity of wind, rain and air, plastic film is generally used to wrap GRC components to avoid direct sunlight, and local humidity can also be maintained by spraying wet fog.
3、在GRC構件的存放和使用過程中，由于其周圍環境與養護階段存在著明顯的差異，因此也是需要進行一定的養護操作的，此時可以采用一些簡單的方式來保證其在存放過程中不會受到陽光的直接照射。
3. During the storage and use of GRC components, due to the obvious difference between the surrounding environment and the curing stage, certain maintenance operations are also required. At this time, some simple methods can be used to ensure that GRC components will not be directly exposed to the sun during storage.
I believe that through reading this article, you have a new understanding and understanding of what should be paid attention to in the use and care of GRC components. If you have any questions, please go to our official website http://m.libpo.com.cn Check, thank you for your reading and support.
